1. When diagnosing an issue, or showing off your tractor or implement, it's important to add images so we all know what you're talking about. Especially when it comes to issues and repairs it's important to include as many images as possible to help our members diagnose your issue. To upload images, use the Upload a FIle button found towards the bottom right of the post response box or a new thread, If you ever have questions please feel free to contact me, My username is Austin.
    Dismiss Notice

MF240 hydraulics ?

Discussion in 'Massey Harris-Ferguson' started by neattouch648, Apr 16, 2009.

  1. neattouch648

    neattouch648 New Member

    Mar 11, 2009
    Hey! i'm new to the forum here, i recently acquired a 1983 massey ferguson MF240, its been sittin in the field for almost a year. I pumped up the tires, put new fuel, and coolant and the tractor started right up (pull-started).

    The only thing that doesn't work on it is the hydraulics, I.E. steering assist, 3 point, etc.

    What is the first thing to check what it could be?

    Any help is much appreciated.

  2. indianajo

    indianajo New Member

    Apr 15, 2009
    make hydraulic work

    On my 245, one of the two valve body handles has to be out for the implement hydraulic pump to be engaged. I had to get the seller to come back out to my field to show me how to do it. If you have the right one, you can hear the hydraulic pump load up. Of course, make sure the hydraulic resevoir has enough fluid. Power steering should work all the time, I think it might be a different pump. Check your transmission sump if you don't find a separate hydraulic filler near the pump at the front of the engine. One circuit may work out of the transmission fluid. After filling an empty sump, have to turn steering full right and then full left to bleed it, then top off again. To bleed implement circuit, hook a hydraulic implement cylinder up to the disconeects, run all way up and down, refill sump. Implement sump can be regular hydraulic fluid, transmission sump should be the more expensive fluid with all the manufacturer rating.
    Last edited: Apr 18, 2009

  3. neattouch648

    neattouch648 New Member

    Mar 11, 2009
    okay, thanks! i appreciate that...what do you mean by the valve body handles?

    Thanks! I got the hydraulic steering to work, the cylinders extend and seem to work properly, the only thing now is they have no power, when they're extending, i can push it together and contract it again.
  4. shona13

    shona13 Member

    Aug 12, 2011
    G.Day neattouch648
    you have two seperate problems
    lets deal with the powersteering first .
    the powersteering has nothing to do with the hydraulics,the power steering pump is in the front right hand side of the engine it has its own reservoir there is a filler level plug remove the plug and filll with dexron two or three the red transmission oil maybe best to first remove the reservoir and clean it out the reservoir is held on by one bolt in the centre it has an "o" ring behind it where it fits onto the pump there is a small filter which has a spring on it either replace the filter or carefully wash out in petrol ,refit and secure the reservoir the nut should have either a fibre or a copper washer to seal it fill with auto trans fluid dexron etc start the engine and run on idle turn the steering wheel full lock left to right a few times to vent the air from the system top up the oil to the BOTTOM of the hole don,t overfill
    or you will get leaks and possibly damage the system.
    P.S .Do not disconnect the power steering rams and turn the steering wheel with the engine running there is vrey high forces in play there and you could easily loose fingers be carefull.
    Second problem
    Hydraulics the Massey 240 Has a mark three hydraulic system If as you say there was water in the hydraulics it is possible that the hydraulic control valve is stuck this is a job for a trained technician ,it should not take more than an hour to fix and i would recommend you get the man.
    The transmission,differential and hydraulics are all common as in they use the same oil refer to local requirements re grade considering temperature etc.
    Te hydrauic filter if it is blocked you will notice the three point linkage shudder ,the filter element is brass or stainless mesh and can be washed out in petrol to access the filter you must first drain all the oil from the differential compartment ,the plug is on the left hand side rear of the tractor7/8 or 15/16 inch ring spanner. the other plug is on the gearbox just below the clutch pedal,remove both and let drain for 1/2 hour 6 gallons capacity.
    the filter cover is on the bottom of the transmission look for a flat surface there is aplate with three bolts 1/2 inch a/f.ring spanner ,remove the cover and you wills see the filter insid eit has a special little clip that goes through the threaded stud to stop the nut coming of ,remove the clip and undo the nut ,pull the filter out and wash in petrol and refit ,make sure you dont forget to put the large "o" ring back on.
    Replace and tighten all plugs and fill with oil .
    May i suggest if you are going to fit a loader or anything that requires hydraulics that you put say an extra 1/2 gallon in to keep the level good.
    Hope this all helps
  5. paul59

    paul59 New Member

    May 10, 2012
    Massey 240 hydraulics - splitter

    I have a MF 240 and am interested in adding a front loader. If anyone has any insight on how to tie this in it would be appreciated.

  6. Lizandbob

    Lizandbob New Member

    Dec 3, 2016
    Where are the hydraulic filters located on a 240massey
  7. BigT

    BigT Active Member

    Sep 15, 2014
    Hello Lizandbob,

    Welcome top the forum.

    The hydraulic filter for a MF 240 is on the underside of the transmission box.

    If your 240 has a loader, this is a separate hydraulic system with a front engine mounted hydraulic pump. The filter is up front of the tractor near the pump.

    It might be wise to get an operator's manual for your tractor. It will detail all maintenance items. You can find an operator's manual on the internet and also on ebay.