Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-15 of 15 Results
  1. Ford / New Holland
    I'm trying to help a neighbor get his Ford 3000 3cyl diesel started. When I turn the ignition switch on, it automatically starts cranking the engine (before turning it further into the spring-return position). Is this normal? It continues to crank by itself until I return the key to the OFF...
  2. Oliver
    I'm looking to find a remanded delco 1109452 starter but not having any luck finding one. Delco says they are discontinued, but I'm sure there is another brand or model number that will fit my Oliver 60 as many parts were interchangeable back then between different equipment manufacturers.
  3. Repair & Technical Discussion
    hi i trying to take my starter out of my leyland 262 tractor i have spent several hours trying to get loose the bolt under the starter and the one by the solinode... no socket fits on it nor a wrench.. how the heck you supposed to remove it 'i have a service manual but it doesnt seem to have...
  4. Case / Farmall - International Harvester
    I recently had the starter for my Case 420b rebuilt. The guy the rebuilt it had a nosecone in a bucket at his shop. He told me if this one broke I was screwed because there wasn't another one anywhere. Do people need these things? Other than me of course. BTW distributor plug wires misconnected...
  5. Repair & Technical Discussion
    Went to start tractor and saw that glow plug light did not illuminate. Glow plug light has come on every engine start so was a bit concerned. Turned switch to "glow plug" and held for appx 10 seconds then turned key to start. Starter did not engage. Thought was low battery so tried to jump from...
  6. Repair & Technical Discussion
    The tractor is having electrical issues. It’s burning up the fuel shut off solenoid. So I put a test light on the positive side of battery and started pulling fuses to see which one would make the test light turn off. So the ignition switch fuse turned it off. I took the dash off and started...
  7. Repair & Technical Discussion
    Hi all, I am new to this forum. I had a starter failure and have purchased a new starter to replace it. I seem to have run into a big problem. There are two bolts/nuts to hold it in place but on this tractor one side has a hidden nut in the flywheel housing (which I had a heck of a time getting...
  8. Ford 9N/2N/8N
    Hello, my name's Davey and i just bought an old Ford 8N tractor. When the man brought it to me, he showed me it was running great. He cut it off and started it several times and it started and ran great every time. Next day i went out to start it and flooded it. I tried to start it again a while...
  9. Repair & Technical Discussion
    I have a 2006 Task Master 425 tractor, with a diesel 385 3 cylinder motor. I am looking to replace the starter, but I have no idea how to determine what model of starter would be compatible or where I could possibly purchase one anywhere. Any insight or advice would be greatly appreciated! Thanks!
  10. Long / Farmtrac / Montana/ LS
    Does anyone have any suggestions (maybe photos, too) of homemade slip covers (PVC sheaths?) or other designs that they use to protect the solenoid/starter assembly wiring from damage during brush-hogging? I’ve assumed the role of operating my father’s Long 2310 to control the ever-invasive...
  11. Projects
    Hello everyone! I recently acquired 1960’s Craftsman that needs some work, and one of the first problems I ran into was the ‘Rachet Self-Starter’ wasn’t functioning properly and I’m not sure how to do work on the piece. Any advice on how to repair one?
  12. Troy-Bilt
    I have an older 80s Troy Built tiller that the starter wont engage. Starter Spins freely and strongly but clutch doesn't seem to allow the gear to engage? Cant find engine or tiller part/ model number anywhere so in the dark here. See the video the clutch seems to be sticking . So the...
  13. Ford / New Holland
    I bought a new starter and got the old one out. Now trying to put the new one in. Big problem! The bottom flange was attached with a nut onto a stud - no problem there. But the top attachment was a bolt connected to a nut on the blind side. I managed to get the bolt out and nut dropped down into...
  14. Chinese / Grey Market Tractors
    I have a Jinma 224 with a Y380 engine that I bought used and it struggles to start. The pics are from a resent clutch replacement as I have been working to get it fully functional. It has always been hard to start... it turns over like the battery is almost dead, but I know it’s fully charged...
  15. Ford / New Holland
    Hello, this is my first time ever to post in a forum. I know very little about tractors or Diesel engines. What I have is a Ford 2110 with a front loader. I4 Diesel engine. At first I had no power to the instrument panel, and found that the power wire from the starter wasn’t attached, fixed...
1-15 of 15 Results
Top