Tractor Forum banner
pump
1-13 of 13 Results
  1. Ford / New Holland
    Range selector in low, gear selector in 1. Tractor barely moves in forward and reverse at max rpms. I suspect the pump has been failing slowly over the last few months because of slower engagement of the gears using high rpms. Pressure at the pump is 1000 psi. Mechanic is sick, now I need to...
  2. Repair & Technical Discussion
    I have a roosa master dbgvcc429-4c, from a 1962 Ford 4000 tractor 4 cylinder, I am rebuilding the pump and in the process I took the cam gear off to clean it and forgot to take a picture of which direction that I was pointing does it go back on clockwise or counterclockwise thanks
  3. Repair & Technical Discussion
    Main Parts List Hydraulic Pump Drive Coupler, 708639M91, $70 Pump Drive Shaft Assembly, 707166M92, $135 19 GPM SAE-B 13 spline counter-clockwise rotation Hydraulic Pump, HGP AL13S-B02-220L, $172 Hydraulic Filter Assembly, 1042326M1, $34 Various hydraulic fittings, adapters, and hoses We...
  4. Repair & Technical Discussion
    Hello, I'm grasping at straws here but I was hoping that another B275 owner with a CAV rotary injection pump might be able to provide me with the "setup number" stamped on the oval plate fastened to the side of the CAV pump. I made the newbie mistake of taking the top cover off the pump to...
  5. Cub Cadet
    I have a cub cadet 5254. Lost hydraulics to deck and pto first. Then lost hydraulics to steering and it stopped moving forward and reverse. My question is does this tractor have a hydraulic pump and transmission or are they both combined in the transmission? Does this sound like a pump issue or...
  6. Repair & Technical Discussion
    gggggggg
  7. Repair & Technical Discussion
    I am rebuilding my hyd pump and ordered a seal kit for mcv and pump. There is a foam seal in the kit and I do not know where it gets installed. It shows it on the parts diagram but not really where it goes. It looks like it has a sticky edge to stick it either to back of pump or someplace...
  8. Ford / New Holland
    While working on a plumbing problem my friend once told me "You can never touch just one fitting". Meaning, once you fix this issue, another will pop up. I suppose the same applies to Diesel Fuel Systems. I had a very simple problem. The cut off lever on the fuel injector pump was leaking...
  9. Projects
    I have a Clear water pump from Harbor Freight laying around and was thinking I could use it for Ballasting my tractor tires but the directions state "Use on Clear Water Only". Why couldn't it be used on other liquids that has no solid chunks, sand, or other pieces of solid material? Brine is...
  10. Repair & Technical Discussion
    Hello again, Working on trying to stop P.S fluid from leaking all over the ground by rebuilding my Ford 4000 power steering ram(cylinder) and found a couple interesting things. 1st thing is that the main cylinder case has a small hole that looks like a valve pin should go there but looks like...
  11. Repair & Technical Discussion
    Hi everyone, Just after opinions on a transmission issue I am having with an old Ford 4500 industrial (loader/backhoe). It has the "Power Reversing Transmission" where you selct a gear and then operate via a foward/reverse lever on the dash - no clutch. Machine was operating well, then stood...
  12. Troy-Bilt
    hi ok here is issue we have a 1995 troy bilt gtx 20 with loader attachment (model 14066) the other night while plowing snow the loader stopped working was fine for hours.. there is no signs of leaks all hoses intacked. no leakage at pump, or control valve.. what would cause this and what should...
  13. Repair & Technical Discussion
    Hi to all ,just found and red post regarding fuel probe on belarus seems to be fixed will pop out and do same fix i hope but i was wondering how much and how fast the fuel should jet out of the top of the pump one port seems to be working but docent seem to be a great amount and the other...
1-13 of 13 Results
Top