Tractor Forum banner

pto

  1. Attachments, Implements & Accessories
    Hey guys, I've recently bought a Case 480c Construction King Loader which were made in 1978-79 (not the same as the older 480 Construction King "CK"). The 480c has a 4-point mount for implements with quick disconnect hydrolics. Currently, I have the 3-point hitch mounted with a box scraper...
  2. PTO

    Simplicity
    Looking for rear PTO for 1970 3212v - any ideas where to find/salvage one? I found one off of a 3212v that is either for a hydrostatic or variable transmission. However, mine is a 3-speed manual and I assume the one from the hydro or variable will not work?
  3. Repair & Technical Discussion
    I recently got a Ford 5000 tractor, it had been sitting for 7 years. Had problems with clutch, but now working. PTO runs for about 10 minutes then quits from a cold start. PTO won't work again until the next day. Any ideas or suggestions would be appreciated.
  4. Repair & Technical Discussion
    I'm new here looking for answers. I have NH TZ25DA. I have noticed the PTO shaft turning when tractor accessories are not attached. In order to attach, I have to turn the tractor off. I am trying to hunt down a repair/service manual. I could sure use a starting point of advice. Thank you
  5. Repair & Technical Discussion
    I recently acquired a 1973 Case 446 with deck & blower. I'm looking to either sell/trade for a tractor with the attachments I need or restore this one and buy 3 point and PTO set up. My question is, is there a one stop shop for all the parts I need? Or, is there any interest in buying it trading...
  6. Cub Cadet
    Greetings, I have a Cub Cadet LTX 1046VT that is being temperamental. I had the machine running and was about to start cutting. When I engaged the PTO the machine stalled. I was unable to deactivate the PTO in time to prevent the stall. After the stall I was unable to restart the machine...
  7. Kubota
    Kubota Bx2370 PTO engage lever was working fine one day the next day first use I noticed the Lever was not returning to the unlocked up disengaged position without help, in fact it is stiff and takes some force to operate it. The spring is connected. Also the Hydro-static foot control is harder...
  8. Classifieds
    This is a great little tractor that fires right up! I purchased the tractor from a maintenance company downtown Cherry Creek Colorado that purchased all the equipment new in1983. The equipment had been sitting for many years without use, I have clean the carburetors new fuel lines clean the fuel...
  9. Repair & Technical Discussion
    I have a 2015 Branson 4720CH, was mowing and the PTO quit working. Fuse is good. Any ideas for troubleshooting the issue?
  10. Kioti
    I have a 2016 Kioti CS2210 with 120 hours on it which I use generally for mowing and snow blowing in the winter. I have performed all the manual-specified maintenance at the specified intervals including replacement of the fuel filter. While mowing yesterday morning i noticed that the...
  11. Gravely / Ariens
    Just got my gravely 526 out for the first time this season. Everything sounds right but the pto will not stay engaged. I was using the 30 in mower Also I have no idea where to add oil to the transmission. Thanks in advance
  12. John Deere
    I have a john deere 415, and the pto will not engage. I have tested the solenoid and renewed the pto switch. I have checked the fuses three which I could find, I really need some help.....
  13. Repair & Technical Discussion
    I have a Ford New Holland 3430 that is leaking fluid out the PTO shaft. I have a new seal just would like advice for replacing it as well as draining and replacing the fluid in the rear end, tranny, and the filter. It is a 2 WD with a dual-speed H/L trans No hydraulics as far as a bucket lift or...
  14. Repair & Technical Discussion
    Hey guys. I've got an old Cushman Frontline mower that's giving me fits.My son took the mower deck off at the end of the season last year to do some work on it.Now I cant get it to slide back on. It doesnt appear bent or damaged and the splines all look OK. Theres no key for it either.It should...
  15. Ford / Jacobsen
    Are there any Replacement PTO CLUTCHES for Ford LGT-100 K-241 Kohler? Any help would be greatly appreciated! The tractor I bought runs great but the PTO Clutch is literally rusted through. Trey
  16. Operating & General Discussion
    All, Recently purchased a Belarus 310 with bucket loader and hooked up my 4 foot brush hog and started mowing. PTO worked fine, shifted right into gear and away I went. A couple days later I returned to run the brush hog again, but for the life of me, could not get the PTO to engage. It was...
  17. Massey Harris-Ferguson
    i have a 265 that has problem lifting implements, when its cold the lift takes about 5 or 10 mins to even start moving then it shudders at any position. normally during warmer months it will lift when tractor starts then gets slower lifting when it runs for a while, but even then it also...
  18. Attachments, Implements & Accessories
    I'm attaching a brush hog and want to know how tight/loose to keep the stabilizers (pictured, orange). Can they be too tight? While running the hog the stabilizer attachment (red) rolled back inside the tractor along with the rods (orange), and the pto was hitting it. I think it happened...
  19. Attachments, Implements & Accessories
    Question: I have this part laying around and I have no idea what it's for... Does anyone know?
  20. John Deere
    Looking for the special pto wrench tool made by MF to change out the PTO spindle from 540 to 1000. Have seen a picture - on one end the wrench has a female 1000 spline and on other end a female 540 spline with a hole in between to insert a bar for leverage. Anyone have one or know where to...
Top