Tractor Forum banner
1-20 of 35 Results
  1. Repair & Technical Discussion
    I recently broke one of the crappy original plastic pistons in my loader joystick and figured I could buy the parts and fix it myself. It didn't seem too complicated but there is one thing that seems to not add up. The replacement piston part (R230282) is structurally different than the...
  2. Ford / New Holland
    Hello all, I have a New Holland TC48DA. I recently installed the controls, valve, and lines to operate the 18LA loader. I order the OEM valve w/controls kit and installed it myself according to the manufacturer’s provided instructions. The description and pictorial diagram provided in the...
  3. Repair & Technical Discussion
    Hey all, I got my first little farm tractor (Ford 600) to start a hobby farm. I consider myself technical, but I’ve got a stumper. The tractor has an aftermarket loader on it. When I got the tractor, the hydraulic lines were rotted out so I had NAPA make me new lines. When I first connected...
  4. Attachments, Implements & Accessories
    Looking for one of these loaders in Michigan to use with my Case 444 tractor. Does anyone have one available or happen to know of another similar model that will fit this tractor? I know there are BYO options but for the moment I don't have a place to attempt this. If it needs work I can do...
  5. Case / Farmall - International Harvester
    I recently came into possession of a Case 444 tractor. I have a lot of jobs to tend to around my property and wondered if there is a factory built Loader and backhoe for this unit? If anyone has model numbers and brands on units that will fit this size tractor I would greatly appreciate it. This...
  6. John Deere
    Has anyone successfully converted a 1987 John Deere Model 67 loader to take quik-change buckets? I am hoping that castings from a later JD model might bolt up to the boom ends and hydraulic cylinders of the 67 with minimal adaptation.
  7. Attachments, Implements & Accessories
    Does anyone know where I can find a loader subframe for a Deutz 7085?
  8. Repair & Technical Discussion
    2007year Montana 4540 Please forgive my limited familiarity with lingo. I want to know the expected source of input for the loader controller. Loader looks factory - Loader and Tractor paint and manuals clearly match. (Color, size, paper, font, poor English, etc.) Yet, loader mount was...
  9. Repair & Technical Discussion
    Main Parts List Hydraulic Pump Drive Coupler, 708639M91, $70 Pump Drive Shaft Assembly, 707166M92, $135 19 GPM SAE-B 13 spline counter-clockwise rotation Hydraulic Pump, HGP AL13S-B02-220L, $172 Hydraulic Filter Assembly, 1042326M1, $34 Various hydraulic fittings, adapters, and hoses We...
  10. Introductions
    Hi Everyone, I have a small orchard in rural So California. Bought a Kubota BX2200 about 6-7 years ago. Came used, has been really reliable with minimal maintenance. Has an issue or two i hope to get answered here! Bob
  11. Kubota
    Kubota Bx2370 PTO engage lever was working fine one day the next day first use I noticed the Lever was not returning to the unlocked up disengaged position without help, in fact it is stiff and takes some force to operate it. The spring is connected. Also the Hydro-static foot control is harder...
  12. Tractors
    Kubota l1700 loader interchangeable with the Kubota l1200 loader
  13. Repair & Technical Discussion
    I bought a tractor that has bent boom arms. The lift works fine but I can see the bucket tilts right to left. I am guessing it is bent 5-10 deg. Are there any suggestions on how to bend it back?
  14. Ford
    Installation, parts and maintenance manual for the freeman bush hog 4000 loader
  15. Kubota
    Hello all, Looking at at Kubota Bx2370 to cut grass and do some work around the yard. Looks good but the bucket drops a couple inches every time it is raised, when the bucket is tilted to raise the tractor off the tires it goes back down immediately. It will lift loads of rocks (boulders) 2 to...
  16. Attachments, Implements & Accessories
    Hi, I have a 1965 MF 202 with a MF100 loader. I have read on other posts that there is supposed to be a dip stick for measuring the oil level. Mine does not have one. Could someone who might have a MF100 loader give me a measurement from the top to the indicated full level?
  17. Massey Harris-Ferguson
    Looking for info on plumbing a joystick valve on my 1135. So far I have found that this tractor has a closed center hydraulic system. But where do I connect the input and tank return lines to the tractor?
  18. Mahindra / Lenar
    I am having a difficult time finding a proper parts diagram and replacement parts for my 2013 Mahindra 4025 loader valve. If anyone has any insight on where I can find these things it would be greatly appreciated. Also, If anyone knows of a good cost effective way to repair it, i'm all ears. I...
  19. Repair & Technical Discussion
    I've read a lot of good advice in these forums so decided to join! I bought a used JD970 with 278 hours. It was garage kept and looks brand new. It came with a loader w/bucket and I promptly bought quick attach forks and added a ballast to the 3PT in the back after the back wheels came off the...
  20. Ford / New Holland
    I am hoping that this video can help out others that may have the same problem that I did. I posted a YouTube video this evening explaining everything in detail. I found out that the only reason everything was gushing out of my lid was because of one wrong oring for my hydraulic sump return...
1-20 of 35 Results