Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 24 Results
  1. Introductions
    Hello there folks I am International tractor mad I currently have a 685 xl, 784 and a 856 xl 4x4. My friends also have 844 xl, 685 4x4 and 474. So plenty of wrenching gets done on case/ internationals! I also have a merlo p32.6 telehandler and a county climax 2.5 tt I am here to gain...
  2. Attachments, Implements & Accessories
    Hi - I've got a topper mower that I'm using for the first time, and I think I must be doing something wrong. I'm hoping it's something obvious and I can hold my hands up for being an idiot. I've got an old International B250, and I believe I have a PTO speed of 540 on this. The PTO shaft from...
  3. Case / Farmall - International Harvester
    Hello, I have an International 756, and I had a question about the throttle. The tractor runs really good. It idles and revs up, but whenever I try to run it over half throttle, the throttle moves back on its own. Unless you manually hold the handle down, which is tuff when bailing...
  4. Case / Farmall - International Harvester
    Hello, I recently bought a 1956 Farmall cub with an IH carburetor, and I had a question about the IH carburetor. Even after rebuilding the carburetor it still leaks gas out into the choke area and onto the ground whenever the gas is turned on and the tractor isn't running. So this is...
  5. Introductions
    Just purchased my first tractor. Going to tinker with in while restoring. Having trouble figuring out what it is! So far I believe it is an International 300 or 350 from 1956. Runs and drives. leaking power steering fluid everywhere! Check out my next post with pics of serial plate and...
  6. Repair & Technical Discussion
    I am thinking about purchasing a gasoline IH 574 with a 835 loader. Guy wants $3500 for it but it currently isn't running right. He said he thinks it has bad gas in it cause when he starts it it runs rough and back fires. He goes to florida for the winter so it didnt get started at all last...
  7. Case / Farmall - International Harvester
    Hello, first post, hope I'm in the right spot. I have an International 385 diesel tractor and the tachometer stopped working. I took it apart and the insides were frozen, looks like some water got in there and rusted pretty good. I tried to get things to loosen up, sprayed with oil and tried to...
  8. Case / Farmall - International Harvester
    When tractor warms up the light will flash and go into limp mode (reduced power and engine speed) code s1076 for inlet metering valve (IMV) can’t really find any information on this. Any help?
  9. Repair & Technical Discussion
    Hello new to the group and just purchased a I2514D what is the chances someone has a manual for it. Not even sure of the year . Thank you in advance
  10. Tractor Pulling
    Hello first let me say I have been a long time lurker of Tractor Forum but first time poster I know you guys have always been super helpful in the Past and look forward to some more help I just got a 1940 Farmall H that I plan on pulling for fun at local events. I know the H cant run much with a...
  11. Operating & General Discussion
    Would a international 656 gas be able to handle a new holland 616 3pt discbine?
  12. Case / Farmall - International Harvester
    Bought my international 460 utility for a little dirt work and tree moving. have been so happy with my purchase! It has a leak in the hydraulics through a hole located on the left side behind the end of the starter where the power steering unit is bolted to the tractor. the power steering bolts...
  13. Buying & Pricing
    Please advise sites that part out old tractors. I have found a couple and have found cylinders for backhoe model 3120 but mine is much bigger model 3140. can I try a cylinder that is not exact match? Here are measurement and I have. Just Hydraulic cylinder tube 47" Hydraulic cylinder from...
  14. Operating & General Discussion
    Hey everyone - I just bought an IH 574. The markings and gauges are all worn off and I'm not sure what all the levers and pedals do. I am good on the PTO engage/disengage, 3 point raising/lowering, choke and all of the stuff I need to know for normal use. But I know there's a differential lock...
  15. Repair & Technical Discussion
    I have a 1979 International 284 gas tractor. I would like to know how the governor is lubricated. Specifically where to lubricate it, fill hole, drain hole, oil viscosity etc. Thank you, Herb
  16. Case / Farmall - International Harvester
    Needing a hood and other misc sheet metal parts for an 885. Anybody know where I can find one?
  17. Classifieds
    Great tractor and a looker too. Sheet metal in great condition, previous owner meticulously repainted every part. Would love to be in a parade. LORD bucket, PTO. Completely overhauled. New Generator. New hydraulic lines. Needs a new fuel line ( will sell with new one) I need smaller hands to...
  18. Repair & Technical Discussion
    I am rebuilding my hyd pump and ordered a seal kit for mcv and pump. There is a foam seal in the kit and I do not know where it gets installed. It shows it on the parts diagram but not really where it goes. It looks like it has a sticky edge to stick it either to back of pump or someplace...
  19. Case / Farmall - International Harvester
    My steering is free wheeling with out turning tires. I get an occasional turn but if I hit a rut my tires automatically turn. I suspect my steering unit has gone bad but would like a second opinion. Thanks
  20. Case / Farmall - International Harvester
    I'm wondering if anyone has had the same issues as me and how they fixed. My case IH 4210 xl cab recently started having gauge problems. It has the digital dash. All of the gauges light up but the information is all wrong. Like it shows the fuel tank completely full, the water temp maxed...
1-20 of 24 Results
Top