Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-16 of 16 Results
  1. Simplicity
    Just picked up a Simplicity Sovereign 7016, model number 1690427 01485. Got is as a project for cheap under the impression it needed less work than it does. No biggie but I'm having a hard time wrapping my head around the vintage ignition system and was hoping for some assistance. As it sits...
  2. Ford / New Holland
    I have a 1971 ford 2000 3 cyl gas tractor the wiring has been chop all to heck, need to know when new from factory did it have a ballast resistor,resistor wire or neither. (Oh howdy everyone new to the site.) Any correct info would help so I will not burn up the coil. Thanks
  3. Massey Harris-Ferguson
    Hi! My dad passed a few years ago and I'm not sure what I'm doing. I lost the key to his Massey Harris 22 (Im pretty sure it's a 1951) so I'm replacing the ignition switch. I've got it in, but there are two connectors on the end - like I need to hook it to the battery but I'm not sure. I don't...
  4. Troy-Bilt
    I own a TROY Bilt Squal Snow Thrower with L Series Tecumseh engine (LH195SP) that has no spark. The magneto ignition coil and spark plug check Ok on my tester. I cleaned the contacts and magnets on the fly wheel and set the gap a .0125. Any suggestions besides buy a new one with a Honda engine...
  5. Case / Farmall - International Harvester
    Good day everyone. Currently having a go at trying to fix up an old International I found in the paddock. I had to order in a new ignition as the old one was missing the slot where the key goes in. Im having trouble finding information on how to install the new ignition, the numbering on the...
  6. Projects
    Well, as the titel says I’m having problems with the ignition on my Massey Ferguson 350 or MF35, I cannot get any spark from the distributor or ignition coil. I have tried to just connect the coil to the battery and open the breakerpoints by hand, still nothing, then I put the spark plug...
  7. Repair & Technical Discussion
    Hey guys new to the forum looking for some help. My grandparents sold their farm and I acquired the equipment on it. I have a 1991 AGCO 4660 and I need some help on the wiring to the ignition switch. Pawpaw thought he was helping and took the old one off and figured I knew what wires went where...
  8. Allis Chalmers
    Hey guys new to the forum looking for some help. My grandparents sold their farm and I acquired the equipment on it. I have a 1991 AGCO 4660 and I need some help on the wiring to the ignition switch. Pawpaw thought he was helping and took the old one off and figured I knew what wires went where...
  9. Repair & Technical Discussion
    I have the original wiring harness (brown, brown, brown/red stripe, white, white /yellow stripe) I bought a new key switch it has 4 blades on it 1-4 with 1 having 2 blades. I can not figure out how to hook this up. Any help would be appreciated
  10. Repair & Technical Discussion
    Why did my new condenser blow? New points and condenser. Tractor ran fine one day and barely ran the next. Now condenser is blown. Its a 6volt system and the guy i got it from put a new 8volt battery in it and said its a common practice. But now condenser is bad. Could the 8 volt battery be the...
  11. Repair & Technical Discussion
    Hey ya'll. I've got a question. I just replaced nearly everything on the ignition system on my tractor. Plugs,wires,coil, cap, rotor and the push button switch.before I did all this it only cranked over 2 or 3 times before it started.Now I have to crank it at least 1/2 a dozen times, stop and...
  12. Repair & Technical Discussion
    hello. Does anyone know if they make a kit to convert my 149 to electronic ignition from points? Thank you. Mike
  13. Ford / New Holland
    Hello, this is my first time ever to post in a forum. I know very little about tractors or Diesel engines. What I have is a Ford 2110 with a front loader. I4 Diesel engine. At first I had no power to the instrument panel, and found that the power wire from the starter wasn’t attached, fixed...
  14. Case / Farmall - International Harvester
    My IH-464 gas will turn over but no spark. When I turn on the key it fires on the first click rather than the start position and sometimes turns over on start position. I have replaced the rectifier and the start switch without any fix. Any suggestions?
  15. Repair & Technical Discussion
    Hey- I have a Ford 2000 unsure of the year but it is a later model with the 3 vents on each side of the hood. Gas engine. I won't get into it, but the ignition was left in the on position for an extended period of time and when I went to start it it was dead. Pulled my truck over and...
  16. John Deere
    Hello everyone! I was mowing today turned the pto off to cross my driveway. When I went to turn the pto back on the engine bogged heavily so I turned the pto off and tried again, once again it bogged I turned the pto off again but the engine shut off. It seemed fairly hot and was smoking so I...
1-16 of 16 Results
Top