Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 36 Results
  1. Repair & Technical Discussion
    Hydraulics are a bit new to me, I've got an old 1966 volvo BM400 with perkins 3 cyl engine and recently hydraulic system was screaming (sounde like noise came from under tractor, now the hydraulics have stopped working, oil level looks quite low so plan is to clean filters and drain and re fill...
  2. John Deere
    Hi all! New to the tractor world. I recently purchased a 1980 2240 independent PTO No Hi/Lo 350,000+SN. I am unable to get any fluid to the front hydraulic pump. I have cleaned the trans. screen (it was very dirty), changed the filter, and cleaned the screen at the front hydraulic pump. I...
  3. Repair & Technical Discussion
    Hi All, New member, first tractor, learning along the way. I purchased an RK37HC about a month ago and have been using it around our five acre property for a variety of projects. Thus far I love it save for just some small quibbles. One of the things that annoys me is that there is no external...
  4. Massey Harris-Ferguson
    First time on a forum but long time reader BACK STORY: We have a 1969 Massey Ferguson 165 gas that my dad has owned for 20+ years. 3yrs ago he rebuilt the motor due it being seized from not being used and being left outside for several years. The tractor runs great but the hydraulics for the...
  5. Attachments, Implements & Accessories
    Does anybody know if I can operate a JCT angle broom standard flow (8-20 gpm) with a Kioti 2610 HST? I will have to run hoses from the rear remotes to operate. TIA.
  6. Operating & General Discussion
    Howdy yall, got a sparky here with no knowledge of hydraulics and new to tractors. I'm trying to understand how to know if/what your tractor (lawn tractor in my case) is capable of performing with its hydraulic system. I'm used to Electric where you start with the load to determine ampacity...
  7. Massey Harris-Ferguson
    G’day, just had an MF168 pulled out the back of my shed a few hundred k’s away and brought up on a flat top. One of the FEL rams didn’t cope well at all and was pouring oil out. I bought and fitted a new one, but had to get the cleavage machined to fit into the FEL arm so it sat for a couple of...
  8. John Deere
    Friend just picked up a nice overall John Deere 400. Hydraulic steering and deck lift. When turning to the left from center, the mower deck and 3 point lever moves and the deck and 3 point lowers while turning. Can't find any physical interference so thinking it may a fault be in the hydraulic...
  9. John Deere
    Hi Folks. I run a 2004 John Deere 4310 with eHydro and a 430 loader. I have a strange hydraulic problem. I have been reading all the forum threads and, though I have learned much, I haven’t yet seen anything that directly addresses my issue. When dumping the FEL bucket (regardless of load), the...
  10. Repair & Technical Discussion
    1974 ford 2000 my lift lever will not move at all. It looks like i have to pull the seat, remove a bunch of 3/4 bolts to remove the cover to get to the bolt that holds the two shafts together. As i see it either a bearing is frozen or the spool is frozen for the raise and lower via the...
  11. Ford / New Holland
    Hello all, I have a New Holland TC48DA. I recently installed the controls, valve, and lines to operate the 18LA loader. I order the OEM valve w/controls kit and installed it myself according to the manufacturer’s provided instructions. The description and pictorial diagram provided in the...
  12. Ford / New Holland
    Well... not only do I have the knocking/injection timing issues, post head gasket replacement, that I posted yesterday, but now, after draining and replacing the hydraulic fluid, I am unable to exceed 1500 or so RPM when running a field mower on the PTO. Changing the hydraulic fluid did resolve...
  13. Repair & Technical Discussion
    Hi I have a leyland was wondering is it possible to test the lift hydraulic without putting the lift top on and the arms
  14. Repair & Technical Discussion
    Hi I have a leyland and was wondering if this link was supposed to move in the photo below and if so if its not is it is it a valve it is controlling and is it stuck?
  15. Repair & Technical Discussion
    I recently got a Ford 5000 tractor, it had been sitting for 7 years. Had problems with clutch, but now working. PTO runs for about 10 minutes then quits from a cold start. PTO won't work again until the next day. Any ideas or suggestions would be appreciated.
  16. Ford / New Holland
    I have a 1969 Ford 3000 Diesel good little tractor About a week ago I was trying to lift something that was too much for the tractor the three point arms dropped and will not even raise with nothing on them. It is full of fluid I have tried to bleed the fluid at the pump. I removed one of the...
  17. Case / Farmall - International Harvester
    Looking for some advice please, had a call out to a 585 that had not been started in nearly 2 years, and owner complaining that Quicke loader was slow and no power steering. Lift arm and draft levers etc were all seized due to lack of use, but managed to free off to a degree! Noticed that the...
  18. Kubota
    Kubota Bx2370 PTO engage lever was working fine one day the next day first use I noticed the Lever was not returning to the unlocked up disengaged position without help, in fact it is stiff and takes some force to operate it. The spring is connected. Also the Hydro-static foot control is harder...
  19. Repair & Technical Discussion
    Have a Koyker KB60 backhoe I am trying to attach to the L185... when I do it seems to disable all hydraulics... when I put it back to the original configuration the bucket works fine... I do not know Hydraulics at all so going blind.... I am sure I am doing some simple hookup wrong...
  20. Repair & Technical Discussion
    RK55 aka TYM. New to tractors 3rd function isn’t working on grapple. It worked a while ago but I have been doing bucket work for two months. When I connected it, hoses and connects looked good and no leaks. When I press the trigger on the implement control nothing happens. The 4 way...
1-20 of 36 Results
Top