Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 23 Results
  1. Ford / New Holland
    We have a 7700Ford with fuel in oil It has a minimec pump on it The drain was plugged and was getting fuel in oil Sent in pump and was repaired Installed and ran about 32 hours and was giving no trouble Now it is getting fuel in the oil again Any ideas? I have checked the overhead...
  2. Massey Harris-Ferguson
    Hello! I am looking for the set code for a CAV fuel pump installed on a perkin 3.152 that power my massey fergusson 50 tractor. I need it because the recommanded static engine timing change with the pump setting. LW45, LW51, PW43,... Here are the 2 numbers I have on the pump nameplate...
  3. John Deere
    I just purchased a John Deere 1050 with a blown head gasket. The tractor ran and I drove it into my shop for the repair. After installing a new head, gaskets, ect, I am having an issue with getting it to run. I have gone through the bleed process several times and I cannot get any fuel to the...
  4. Kubota
    If you look at my past post you'll see I've been fighting this for a long time. Basically the tractor starts sputtering then it dies. First time this happened I took off the gas tank cleaned out completely, used a pressure washer on the tank, changed out the fuel filters and it ran perfectly...
  5. Repair & Technical Discussion
    On an old mower (F525) I am replacing the old carburetor and it has a backfire solenoid valve, but it was broke and I tossed it in the garbage. I got a new carburetor to replace the old one and saw that the bowl plug (where the backfire solenoid screws into the bowl) has a needle valve attached...
  6. John Deere
    Purchase my first diesel, an 02 John Deere X595 with 1100 hours. Yanmar 3TNE74 engine. Takes a few minutes to start. Doesn't want to crank over, like its not getting fuel but once it does I am set. It will continue to fire right up until I leave it sit over night. No loss of power or anything...
  7. Kubota
    I have changed fuel filters before but I don't remember if the filter fills completely with fuel or not? If it should be full why would this one not fill completely? A. bad filter? B. hole in filter? C. something else? D. Wont there be problems...
  8. Kubota
    Kubota Bx 2370 started and mowed deep grass for about a half an hour and it started to die out like it was under to much of a load but not the case. On flat land it ideals fine but dies when facing up hill. it goes up hill and runs fine backwards flat or hill land. Fresh fuel in it but did not...
  9. Repair & Technical Discussion
    Hello, I have a IH 2400A front end loader. 1972 ish. I have serial numbers for all. It died on me suddenly. I've replace points cap rotor plus wires coil fuel pump carb rebuild kit but now it is just running to rich or to lean. How can one thing starting out to be electrical end up now with...
  10. Repair & Technical Discussion
    Our Massey Ferguson 165 tractor's fuel gauge has never worked. The fuel gauge was bad but I was able to order a new one (p/n: 1074336M9) for $20 here...
  11. Husqvarna
    Hi guys and gals, I got a Husqvarna Lgt2654 about 3years ago and untill now never had a problem with the Kholer command engine. At first it would die when i was mowing and it was hot, now it wont run with a load (mower engaged) on it. It will sit there and run at idle all day, but when I engage...
  12. Ford / New Holland
    Hello All, Just a quick question for you diesel experts. Taking my top cover of my CAV off and I had to cut my fuel line backflow tube that goes to the overflow of my injectors. My question is can Air line for brakes be used? It looks the same and the ID is the same(1/4)(?) The NAPA mgr said...
  13. Ford / New Holland
    I used my 69 Ford 4000 Diesel in June, went to start it 3 days ago (9/24/2019) and it just turned over and over and over. Sucked out all the fuel, replaced with new "Off Road Diesel" and used some Hot Shot’s Secret "Diesel Extreme" Fuel conditioner. It started on the 1st try, easy, peasy...
  14. Repair & Technical Discussion
    ive got a mxm 175 that’s been giving me fits running as of late. Started off by not starting for a whole day, would crank but not fire. Checked all fuses and relays to be ok and nothing. Finally started after sitting. Disced a field the following day only to have it cut power on its own and...
  15. Ford / New Holland
    While working on a plumbing problem my friend once told me "You can never touch just one fitting". Meaning, once you fix this issue, another will pop up. I suppose the same applies to Diesel Fuel Systems. I had a very simple problem. The cut off lever on the fuel injector pump was leaking...
  16. John Deere
    I have a old lt150 that has a lot of problems but it cuts and usually runs better than my 2 yr old husqvarna. It turns but no start. New gas after the tank was cleaned and new fuel filter. Fuel pump gets gas to the carb intake. Poured gas into carb and it runs till gas runs out. Is there a...
  17. Repair & Technical Discussion
    All, Having fuel leakage and low pressure issues with my Belarus 310. Does anyone have a link to a HOWTO to refurbish the primary and the secondary fuel pumps for my tractor. I ordered new hand primer pump and the two fuel filters for it. Is there a gasket/seals kit for my 2 pumps? If so...
  18. Ford / New Holland
    I’ve got a Ford 5000 with the minimec pump and dual fuel filters. Tractor recently started surging and will die. Upon further investigation, I have found that after the engine dies, the second fuel filter (one closest to the injection pump) will not have fuel in it while the first filter will. I...
  19. John Deere
    Older jd dt150 mower. Runs fine while gas that i poured in crab is there. Gas has been replaced and gets to the float/bowl without issues and filter is new. Any ideas why the gas wont travel from the float/bowl into the cylinder to be fired upon?
  20. Operating & General Discussion
    I did something dangerous the other day, I read, I read a story about Bio-diesel and that you can make it yourself and would cost about $1.00 per gallon to make, that is after finding a couple of containers for 1- for seperating oil from the H2o and fried chunks. 1- for Processing and mixing -...
1-20 of 23 Results
Top