Tractor Forum banner

ford 4000

  1. Repair & Technical Discussion
    Hi everybody. I was wondering if anyone could tell me what this part is called, (marked with an arrow in the picture) as I'm going to replace the sealings around it, but I cannot even order the right parts. Any help will be appreciated. Philip
  2. Repair & Technical Discussion
    I have a 64 Ford 4000 4 cylinder gasser I’ve been fooling with. I’m having problems with intermittent spark. I’ve replaced coil, points, rotor, plugs and wires. When the cap is off I usually only get spark between the points after letting go of the starter button. When holding a plug to the...
  3. Ford / New Holland
    Hur hittar jag TDC på Ford 4000 ?
  4. Ford / New Holland
    Hi there im thinking about purchasing a single spool valve kit for my Ford 4000. I still have the original switch on the tractor for the single pipe. When I pull out the switch the 3 point arms lock in place and I use this when pulling a trailer to keep the linkage arms up high. I am wondering...
  5. Repair & Technical Discussion
    I just inherited a 1967 Ford 4000 3-cyl Diesel tractor with a new home. It was sent off to service just before the purchase so fluids were replaced. Everything is working well except for the three point hitch in Position Control mode. The rear implement doesn't track the position control lever...
  6. Repair & Technical Discussion
    I am having a hard time finding a governor assembly for a my ford 4000 3 cylinder 1971 tractor. All that I find online are for a 4 cylinder. any help? or could the one for the 4 cylinder work for the 3 cylinder?
  7. Ford / New Holland
    I am hoping that this video can help out others that may have the same problem that I did. I posted a YouTube video this evening explaining everything in detail. I found out that the only reason everything was gushing out of my lid was because of one wrong oring for my hydraulic sump return...
  8. Ford / New Holland
    First I want to thank you for all the help that I have received. I have used tractors most of my life but never had to work on one. This my first rebuild and the last thing I need to do is replace the o-ring on the lower flow tube on the Ford 4000 tractor. While reading the service manual, it...
  9. Repair & Technical Discussion
    Good evening or morning where you are. I have a question for anyone that can help me. I have a leak at my manual steering gear box and after closer examination it is where the throttle plate attaches to the main steering gear box plate. Does anyone know a way to disconnect the throttle handle...
  10. Ford / New Holland
    Hi all. I know this is a stupid question but I am having issues with the drawbar on my ford 4000 tractor. I never used it before and I am having difficulty putting the clip into the pin while the drawbar is in place. If someone could explain to me how/where the pin goes I would be very greatful.
  11. Ford 9N/2N/8N
    Help! I have found some more numbers on my used Ford 420. It just adds to the mystery. Can someone help me figure out what I have? Here are the previous numbers I found on the flat portion behind the starter on the right side. B886256 OE26 D1014C The new information I have is numbers...
  12. Ford / New Holland
    Help! I have found some more numbers on my used Ford 420. It just adds to the mystery. Can someone help me figure out what I have? Here are the previous numbers I found on the flat portion behind the starter on the right side. B886256 OE26 D1014C The new information I have is numbers...
  13. Ford / New Holland
    Let me 1st say I don't know what is the correct word is or the difference is between hydraulic controls and remotes? I have a 1969 Ford 4000 and it has a dual(2 levers)(4 hose connections) remote/control. How much value should that add to a tractor? Is this stock for this year? I looked online...
  14. Tractors
    This is a scan PDF for the Ford 2000/3000/4000/5000 Operators Service Manual
Top