Tractor Forum banner

case

  1. Attachments, Implements & Accessories
    Hey guys, I've recently bought a Case 480c Construction King Loader which were made in 1978-79 (not the same as the older 480 Construction King "CK"). The 480c has a 4-point mount for implements with quick disconnect hydrolics. Currently, I have the 3-point hitch mounted with a box scraper...
  2. Repair & Technical Discussion
    I recently bought a 1979 995 Case Tractor and do not have a manual for it. I need to know how to change a stuck valve in the rear hydraulic lift system.
  3. Repair & Technical Discussion
    I recently acquired a 1973 Case 446 with deck & blower. I'm looking to either sell/trade for a tractor with the attachments I need or restore this one and buy 3 point and PTO set up. My question is, is there a one stop shop for all the parts I need? Or, is there any interest in buying it trading...
  4. Repair & Technical Discussion
    hi guys I'm wondering if anyone can help me with a problem on my case 1170 cvx we had the transmission out for an overhaul and when it was refitted it won't move and it shows an error code of sgr 148 and 245 and help would be greatly appreciated
  5. Operating & General Discussion
    Hey everyone - I just bought an IH 574. The markings and gauges are all worn off and I'm not sure what all the levers and pedals do. I am good on the PTO engage/disengage, 3 point raising/lowering, choke and all of the stuff I need to know for normal use. But I know there's a differential lock...
  6. Repair & Technical Discussion
    I am in search of a front spindle for my case 1290. I am going to attempt to supply a drawing with the measurements required. I have had NO luck with the popular tractor parts dealers. In fact, I have ordered 2 spindles neither of which fit to the tune of $100 in shipping and restocking fees out...
  7. Case / Farmall - International Harvester
    Needing a hood and other misc sheet metal parts for an 885. Anybody know where I can find one?
  8. Repair & Technical Discussion
    Blew a head gasket on my Case 580ck. Has a 188D engine. This will be a simple question.. Is there a need to remove the push rods before removing the head? I have searched and not found anything regarding this on this engine. Not a lot of diesel perience on this of the screen.. So be easy!
  9. Operating & General Discussion
    On my farmall the 3pt arms raise just fine but they lower so slowly that they are basically unusable. I’ve tried messing with the adjustment next to the right armrest but it makes no difference. Any ideas as to what is causing this issue?
  10. Repair & Technical Discussion
    Hi everyone, new here. I have a case 895 I had to split. The TA just gave up. I got that sorted but now I'm having trouble getting it back together. The dowel pin on the bell housing won't line up with the block. Iv tried jacking from both sides to line up but won't go through. Any tips appreciated!
  11. Repair & Technical Discussion
    I have a Case JX - 75, believed to be a 2004 or 2005 model. We purchased it off of AuctionTime last fall; the tractor grinds going into forward -- to the point that the tractor is not able to be driven. I briefly searched the Internet and Facebook for any local repair shops, but was looking for...
  12. Case / Farmall - International Harvester
    I am new to Case tractors. I am currently looking at one for sale. I have not seen it in person these are the only photos I was sent. Could someone please help me with some info. I was looking for model, year, etc. I would also like to what I should pay for this tractor. It doesn't run but was...
  13. Repair & Technical Discussion
    Hi guys looking to see if anyone has info relating to a couple things , the ECU in a case cvx 130 I bought had been stolen and I have sourced a replacement unit correct part numbers but from a CVX 150 I am guessing it wont operate the 130 until the software is updated and setup for the 130 is...
  14. Case / Farmall - International Harvester
    So I have a guy working on my Case 380CK (David Brown 885) and he was able to remove the control valve for the 3 point hitch. He disassembled it, cleaned it up, and re assembled it. He also drained all hydraulic fluid and put new in. After doing so the hitch would raise and lower but at a...
  15. Case / Farmall - International Harvester
    Has anyone here tried their hand at removing and cleaning the control valve for the 3-point on one of these? I am having the hardest time removing it and suspect a dirty valve is the culprit for why the hitch wont raise or lower. There are a few videos on YouTube of guys working on these but...
  16. Case / Farmall - International Harvester
    Guys I have a case 380ck and the 3Point raises when I turn the tractor on but then doesn’t respond to the control arm to lower. I’m posting some pics here where I have removed the cover over top the control valve and the cover to expose the sensing cable linkage. Looks to me it’s dry as a bone...
  17. Repair & Technical Discussion
    My Case IH 4210 MFWD with Cab and the 16x8 transmission (partial power-shift) won't shift into low range. I can shift into high range and reverse with no issues. Rabbit/turtle power-shift working fine too. When I try to shift into low range it'll just grind gears. Need new clutch? Or is there...
  18. Repair & Technical Discussion
    so guys the other day i had a hydraulic pipe burst on the cx75 and lost quite a bit of oil... wasn’t a hard hose to replace... so I stuck a drum of oil in it and run it after to test for leaks and everything worked fine... I later filled up hyd oil to the right level and everything other than...
  19. Case / Farmall - International Harvester
    Guys, I have come across a Case tractor on my grandfather's farm that I cant seem to identify. He was a fan of scraping off markings and plates because "the government dosent need to know what I'm doing." I have posted a few photos here and was wondering if anyone can point me in the right...
  20. Repair & Technical Discussion
    hi everybody and thank you for accepting me as your new friend. im here to help and also always appreciate help. im a farmer and also mechanic by trade. i rebuild tractors as a hobby and part time income i would like to offer my professional knowledge to help others. i have workshop or...
Top