Tractor Forum banner
backhoe
1-20 of 23 Results
  1. Case / Farmall - International Harvester
    IH 2514B (FEL + backhoe version) Everything was working fine just a couple of days before. I went out to move it to a different spot and as I was turning a corner I felt like something was wrong. Within another 50 feet or so I had no steering. The FEL works. The backhoe works except for the...
  2. Attachments, Implements & Accessories
    Hey guys, I've recently bought a Case 480c Construction King Loader which were made in 1978-79 (not the same as the older 480 Construction King "CK"). The 480c has a 4-point mount for implements with quick disconnect hydrolics. Currently, I have the 3-point hitch mounted with a box scraper...
  3. Case / Farmall - International Harvester
    I recently came into possession of a Case 444 tractor. I have a lot of jobs to tend to around my property and wondered if there is a factory built Loader and backhoe for this unit? If anyone has model numbers and brands on units that will fit this size tractor I would greatly appreciate it. This...
  4. Repair & Technical Discussion
    Happy New to all! Been a few months since I last posted - been a bit busy. I have a Branson (BH86 Kukje) backhoe. I dropped a large log (not intentionally of course...) on to one of the fittings on the stabilizer. There looks to be a fitting that goes in to the hydraulic tube - the 90 degree...
  5. Attachments, Implements & Accessories
    So I bought a 2004 Nortrac NT254 last January that was gutted to fix the previous owners other Nortrac NT254... Axle was broken, electrical torn apart, cooling system rusted out, hydraulics leaking terribly, clutch slipping but for $1000 it seemed like a great deal. Over a few months and...
  6. Buying & Pricing
    Please advise sites that part out old tractors. I have found a couple and have found cylinders for backhoe model 3120 but mine is much bigger model 3140. can I try a cylinder that is not exact match? Here are measurement and I have. Just Hydraulic cylinder tube 47" Hydraulic cylinder from...
  7. Repair & Technical Discussion
    Ford 555 has a 3 cylinder diesel with a turbo that looks aftermarket. Ive had it 6 months and it has been working great until yeasterday It wouldn’t turn over. The engine was hydro locked with fluid in the cylinders (mostly the rear one) when i removed the injectors it woud turn over and sprayed...
  8. Kubota
    Old pressure relief valve from BH 90 backhoe removed and replaced with new valve (for $800, sigh). This old valve is available to someone interested in refurbishing it for personal use of resale. BH 90 backhoe attachment is working fine with new valve, though I am considerably poorer as a...
  9. Ford / New Holland
    Mid 80's Ford 1310 w/770B loader. I might purchase. My question is can a backhoe be attached to this particular tractor? Thanks.
  10. Attachments, Implements & Accessories
    I have recently bought a tractor with a Kubota backhoe attachment but could not find a model number that needs the bucket replaced looks like in too bad of shape to be repaired. Can anyone help determining the model or what replacement bucket I can use. I have attached a picture of the bucket
  11. Ford / New Holland
    Hi. I am about to do a larger service on my Ford 550 backhoe, and are have got my hands on chapter 1 of the repair manual, but it refers to chapter 3 with the specifications where the torque specs are listed... And I need those specs to make sure to not overtighten things. Anyone got that...
  12. Repair & Technical Discussion
    Hey everyone, i just got my father's 3pt woods backhoe hooked up to my tractor. It was operational last time I saw it, my uncle borrowed it and broke the pump. He said he replaced the pump, but must have done something wrong because it's slow. Shortly after that he purchased a new kubota with...
  13. Ford / New Holland
    Hi! My Ford 550 backhoe loader have started to make a bang/loud knock every time it cranks one turn. It sounds like a much louder compression like, or, as said, a bang or a loud knock. It gets louder when you gas up and the RPM's rises and the knock rises as the rpm's goes up. It starts 10-15...
  14. Long / Farmtrac / Montana/ LS
    I just recently replaced one of my hydraulic lines and was hoping to have the air bleed out on its own while operating with no load. Well, it didn't quite happen like that. Seems like the hydraulic oil level went too low on an incline and I got air in my circuits. I still have most of my...
  15. Repair & Technical Discussion
    I have a Branson 3120 with a Bh 86 Kukje backhoe. The backhoe has been sitting for a couple of years. I need to move it but when I connected the hydraulic lines there is no power to the boom or to the stabilizers. It operated fine before I disconnected and stored it. Any ideas? Air lock...
  16. Attachments, Implements & Accessories
    I bought a used (of course) JD850 with backhoe. The swing cylinders were not attached to the boom and the seller said they were reworked but never attached. I tested them before attaching by activating (push lever) and watch for cylinder movement. Nothing happened! I want to narrow down the...
  17. Repair & Technical Discussion
    Hi all, this forums been amazing in the past so here goes again! I have a Dongfeng issued DaxTrac. Recently purchased a backhoe attachment (Kelly 50) for it. Being too dumb to leave well enough alone, I decided to remove the auxiliary pto driven pump on the backhoe attachment and run it from my...
  18. Snapper
    Im building a front end loader and a backhoe for my Snapper 1650. I hope you will follow along and check it out. I have pictures , Ill have more later. So far I have managed to completely disassemble my tractor, thought I might as well rebuild it too.
  19. Introductions
    Im new to this forum, so Ill explain what I have and what I am Doing. I have a Snapper 1650, I think its about a 1974. Anyway I am building a front end loader and a backhoe for it. It should be interesting, so you can follow me here.
  20. Ford / New Holland
    Hello, I have a ford 550 backhoe and I can not identify the manufacturing codes. on the right side of the engine below the injector pump I found the following data: XA 60N05 0m64 in the middle of the engine block is 4.4 NW on the left side of the motor HN2 0k04 Someone can help me?
1-20 of 23 Results
Top