Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-13 of 13 Results
  1. Buying & Pricing
    ISO a 1993 ford 4630 201 diesel engine, if it needs rebuilt that is fine. my block has a quarter size piece missing from the bottom of the cylinder wall, due to a rod cap coming off, bought that way, does need to have a cam and crank in the engine, im located in oregon so will have to be...
  2. Repair & Technical Discussion
    I have a roosa master dbgvcc429-4c, from a 1962 Ford 4000 tractor 4 cylinder, I am rebuilding the pump and in the process I took the cam gear off to clean it and forgot to take a picture of which direction that I was pointing does it go back on clockwise or counterclockwise thanks
  3. Introductions
    Hello everyone, I'm new to this form and still trying to figure out exactly how it works, anyways long story short I purchased a tractor about a year ago it's a Ford 4000 with skip loader, not sure of the exact year but when I resealed the injection pump it had 1962 stamped on the inside so I'm...
  4. Ford
    Installation, parts and maintenance manual for the freeman bush hog 4000 loader
  5. Ford / New Holland
    Simple question. 1969 Ford 4000 Diesel. Need Torque Specs for the top cover of the CAV. I can't find any listed in the service manual. Can anyone help me? Is there a torque value? Thanks, OMF
  6. Ford / New Holland
    Hello All, Just a quick question for you diesel experts. Taking my top cover of my CAV off and I had to cut my fuel line backflow tube that goes to the overflow of my injectors. My question is can Air line for brakes be used? It looks the same and the ID is the same(1/4)(?) The NAPA mgr said...
  7. Ford / New Holland
    I used my 69 Ford 4000 Diesel in June, went to start it 3 days ago (9/24/2019) and it just turned over and over and over. Sucked out all the fuel, replaced with new "Off Road Diesel" and used some Hot Shot’s Secret "Diesel Extreme" Fuel conditioner. It started on the 1st try, easy, peasy...
  8. Ford / New Holland
    Good evening. I have a small leak and tried everything I can think of to raise the pipe to replace the o-ring. I cleaned the pipe, I was trying to use pliers, and basically everything I can think of without destroying the tube. Has anyone replaced the o-ring in the tube and if so how did you...
  9. Operating & General Discussion
    3 years ago there about I bought a 54" cut 26 hp Lawn tractor (they said Garden Tractor) and each year something goes wrong. 1st was the bad cut, UN-even and choppy. then I found out that blades get bent. The ground is hilly but does not have any obstacle that would bend the blade or any thing...
  10. Ford / New Holland
    Hello again all, 1969 Ford 4000. The last 2 times I used it it started to sound like one of the 3 cylinders went missing. The 1st time I only ran it for a short time after it started to sound like a missing cylinder. The next time I started it, it sounded fine, in fact I forgot about the sound...
  11. Repair & Technical Discussion
    I am having a problem find the proper torque for the (4)cap screws #48 in diagram attached and the castellated nut #23 in diagram attached for the valve spool bolt #35 in diagram attached. The Spec sheet attached is not clear.
  12. Repair & Technical Discussion
    Hello again, Working on trying to stop P.S fluid from leaking all over the ground by rebuilding my Ford 4000 power steering ram(cylinder) and found a couple interesting things. 1st thing is that the main cylinder case has a small hole that looks like a valve pin should go there but looks like...
  13. Ford / New Holland
    1969 Ford 4000 Diesel, Power steering is Leaking in 2 places so I want to rebuild it but I'm finding conflicting information and parts. My tractor does not have a fluid reservoir, and the service manual show that it should have one and the ram is different. The parts manual shows other styles of...
1-13 of 13 Results
Top