 |
06-19-2010, 09:27 AM
|
#1
|
|
Registered User
Join Date: Jun 2010
Posts: 2
|
Kubota g2160 power steering.
Hi, I have a Kubota G2160 and the power steering has stopped working. I have stripped most of it down and discovered the control box has an LED flashing 1 long and 3 short. I asume this is a fault code.
Does anyone know what 1 long and 3 short flashes mean, it does it from when the ignition is switched on and with the engine running and won't stop untill switched off?
I have tested the motor and it works fine. There is a sensor but I can't remove it its stuck in the steering coloumn.
I have a parts manual and the whole steering column has to be replaced, individual parts aren't available. I have a feeling this is going to be expensive.
Has anyone had this before?
Thanks,
Niguk68.
|
|
|
|
06-21-2010, 12:15 PM
|
#2
|
|
Registered User
Join Date: Jun 2010
Posts: 2
|
Update,
I got some good help from a dealer today and it didn't cost a penny. The problem may be that we fitted a new ball joint a few weeks ago between the steering rack and the front axle. After this you should re calibrate the steering because if you are out by a small amount the control box trows a wobbly.
The dealer faxed me through, firstly how to re set the control box and then re calibrate the steering. Once I did it it started working fine.
If anyone wants the proceedure send me a message and I will forward it. No special tools required but you have to remove the plastic cover that covers the steering and control box.
|
|
|
|
|
06-21-2010, 01:52 PM
|
#3
|
|
ENGLISH SPRINGER SPANIELS
Join Date: Jan 2010
Location: Hoodoo Valley, Idaho
Posts: 5,449
Liked 3 Times on 3 Posts
|
Glad to hear that you got it up and running again.
__________________
Oh Beautiful for smoggy skies, insecticided grain,
For strip-mined mountain's majesty above the asphalt plain.
America, America, man sheds his waste on thee,
And hides the pines with billboard signs, from sea to oily sea. _______________________________________________ Some say I have a bad attitude...... "Screw them!"
|
|
|
|
|
08-25-2010, 08:59 PM
|
#4
|
|
Registered User
Join Date: Aug 2010
Location: Batavia, NY, NY
Posts: 2
|
G2160
Quote:
Originally Posted by niguk68
Update,
I got some good help from a dealer today and it didn't cost a penny. The problem may be that we fitted a new ball joint a few weeks ago between the steering rack and the front axle. After this you should re calibrate the steering because if you are out by a small amount the control box trows a wobbly.
The dealer faxed me through, firstly how to re set the control box and then re calibrate the steering. Once I did it it started working fine.
If anyone wants the proceedure send me a message and I will forward it. No special tools required but you have to remove the plastic cover that covers the steering and control box.
|
help ! I have the same problem. Could you forward the info to me ? Email address is davehowe10@gmail.com THANKS!!!!!!!
|
|
|
|
|
09-06-2010, 01:47 PM
|
#5
|
|
Registered User
Join Date: Sep 2010
Location: hillsboro, illinois
Posts: 1
|
I too have this problem and am also in need of the info please send it to jfrapp@consolidated.net thank you in advance for your cooperation
|
|
|
|
|
09-17-2010, 01:39 PM
|
#6
|
|
Registered User
Join Date: Sep 2010
Location: swansea, carmarthenshire
Posts: 2
|
Hi i to have the same problem could you send it to deborah274@btinternet.com thank you very much Mark
|
|
|
|
|
09-19-2010, 12:34 PM
|
#7
|
|
Registered User
Join Date: Sep 2010
Location: swansea, carmarthenshire
Posts: 2
|
Quote:
Originally Posted by niguk68
Update,
I got some good help from a dealer today and it didn't cost a penny. The problem may be that we fitted a new ball joint a few weeks ago between the steering rack and the front axle. After this you should re calibrate the steering because if you are out by a small amount the control box trows a wobbly.
The dealer faxed me through, firstly how to re set the control box and then re calibrate the steering. Once I did it it started working fine.
If anyone wants the proceedure send me a message and I will forward it. No special tools required but you have to remove the plastic cover that covers the steering and control box.
|
hi can you send me that info again as I gave you wrong e-mail address it's deborahjones274@btinternet.com thanks mark
|
|
|
|
|
08-16-2011, 03:37 PM
|
#8
|
|
Registered User
Join Date: Aug 2011
Location: Pulaski, Va
Posts: 3
|
Do you know how to do this on a TG1860G?? Same problem with the steering.
|
|
|
|
|
08-18-2011, 06:59 PM
|
#9
|
|
Registered User
Join Date: Aug 2011
Location: Pulaski, Va
Posts: 3
|
Can anyone tell me how to correct the steering??
|
|
|
|
|
10-19-2011, 01:52 PM
|
#10
|
|
Registered User
Join Date: Oct 2011
Location: Glasgow, Ayrshire
Posts: 2
|
Quote:
Originally Posted by niguk68
Hi, I have a Kubota G2160 and the power steering has stopped working. I have stripped most of it down and discovered the control box has an LED flashing 1 long and 3 short. I asume this is a fault code.
Does anyone know what 1 long and 3 short flashes mean, it does it from when the ignition is switched on and with the engine running and won't stop untill switched off?
I have tested the motor and it works fine. There is a sensor but I can't remove it its stuck in the steering coloumn.
I have a parts manual and the whole steering column has to be replaced, individual parts aren't available. I have a feeling this is going to be expensive.
Has anyone had this before?
Thanks,
Niguk68.
|
Could you please e-mail me the info on the steering to fraserhlang@yahoo.co.uk.
thanks
|
|
|
|
|
05-03-2012, 05:03 PM
|
#11
|
|
Registered User
Join Date: May 2012
Posts: 1
|
G21 Sttering Repair
Hi... Can you send me the procedure for the G21 repair on the electric steering alignment. I have the same problem as you described. My e-mail address is tomobrien0007@gmail.com...... really appreciate that (From Ireland)
Quote:
Originally Posted by niguk68
Update,
I got some good help from a dealer today and it didn't cost a penny. The problem may be that we fitted a new ball joint a few weeks ago between the steering rack and the front axle. After this you should re calibrate the steering because if you are out by a small amount the control box trows a wobbly.
The dealer faxed me through, firstly how to re set the control box and then re calibrate the steering. Once I did it it started working fine.
If anyone wants the proceedure send me a message and I will forward it. No special tools required but you have to remove the plastic cover that covers the steering and control box.
|
|
|
|
|
| Thread Tools |
|
|
| Display Modes |
 Linear Mode
|
|
|
|
